Apr 24, 2024 JN0-363 Exam Crack Test Engine Dumps Training With 293 Questions
Obtain the JN0-363 PDF Dumps Get 100% Outcomes Exam Questions For You To Pass
NEW QUESTION # 173
You are establishing RSVP LSPs through your MPLS-enabled network. You are asked to ensure that the LSPs will support end-to-end class-of-service handling.
Which statement is correct in this scenario?
- A. Configure entropy-label on the egress device.
- B. Configure explicit-null on all MPLS-enabled devices.
- C. Configure implicit-null on all MPLS-enabled devices.
- D. Configure ultimate-hop-popping on the egress device.
Answer: B
NEW QUESTION # 174
Click the Exhibit button. You configured an aggregated Ethernet bundle between R1 and R2. Unfortunately, the bundle is not working correctly.
Referring to the exhibit, which configuration change will solve this issue?
- A. The LACP minimum links configuration should be changed to 2 on R1.
- B. The LACP minimum links configuration should be changed to 1 on R2.
- C. The LACP periodic mode should be changed to fast on R2.
- D. The LACP mode should be changed to active on R1.
Answer: D
NEW QUESTION # 175
Exhibit
The routers shown in the exhibit ate configured for segment routing.
In this scenario, what is the adjacency SIO that Router B advertises to Router A?
- A. 10.1.1.2
- B. 10.1.1.1
- C. 0
- D. 1
Answer: C
Explanation:
The adjacency SID in segment routing is advertised by one router to inform another about the label that should be used to forward traffic to it over a particular link. In this scenario, Router B would advertise an adjacency SID to Router A, which would be usedby Router A to forward traffic to Router B. Based on the exhibit, the adjacency SID that Router B advertises to Router A would be 12.
References:
Juniper Networks documentation on Segment Routing: Segment Routing Overview
NEW QUESTION # 176
Click the Exhibit button. From the output shown in the exhibit, what would happen to a packet destined for address 172.29.3.5?
- A. The address is not in the aggregate range; the packet will be forwarded.
- B. The address is in the aggregate range; the packet will be silently dropped.
- C. The address is in the aggregate range; the packet will be dropped.
- D. The address is not in the aggregate range; the packet is sent to the Routing Engine.
Answer: C
NEW QUESTION # 177
Click the Exhibit button.
Referring to the exhibit, which statement is correct?
- A. Routes from 10.1.1.1 are less preferred than the default local preference
- B. Routes from 10.1.1.1 are less preferred than routes from 10.2.2.2
- C. Routes from 10.2.2.2 are less preferred than routes from 10.1.1.1
- D. Routes from 10.3.3.3 are less preferred than the default local preference
Answer: C
NEW QUESTION # 178
Referring to the exhibit, which two statements are correct? (Choose two.)
- A. Prefixes in Level 1 will not be redistributed to Level 2.
- B. Prefixes In Level 2 will be not redistributed to Level 1.
- C. Prefixes in Level 1 will be redistributed to Level 2.
- D. Prefixes in Level 2 will be redistributed to Level 1.
Answer: B,C
NEW QUESTION # 179
You are setting up a new IS-IS adjacency between two devices. The new Level1 adjacency is not establishing.
What would cause this behavior?
- A. The Level 1 routers have mismatched area IDs.
- B. The routers support a minimum MTU of 1492 bytes.
- C. The router ID has not been explicitly configured.
- D. The IP addresses are on different subnets.
Answer: A
NEW QUESTION # 180
Exhibit
Referring to the exhibit, what is the minimum number of LSPs required to support alt four networks?
- A. 0
- B. 1
- C. 2
- D. 3
Answer: D
NEW QUESTION # 181
You have just configured IPv6 in your network. A packet arrives on your router that exceeds the MTU size. How will an IPv6 router respond?
- A. The packet is kept intact and not fragmented.
- B. The fragment offset is referenced and the packet is fragmented.
- C. The packet is fragmented based on extension headers.
- D. The packet is dropped.
Answer: D
NEW QUESTION # 182
You have configured graceful RE switchover (GRES), however you cannot complete the show system switchover command.
Referring to the exhibit, what is the problem?
- A. The command is only available If a backup router is configured.
- B. The command is only available on the backup Routing Engine.
- C. The command is only available if non-stop routing is enabled.
- D. The command is only available If graceful restart is enabled.
Answer: B
Explanation:
Issue the show system switchover command only on the backup Routing Engine. This command is not supported on the primary Routing Engine because the kernel-replication process daemon does not run on the primary Routing Engine. This process runs only on the backup Routing Engine.
NEW QUESTION # 183
Click the Exhibit button. The policy shown in the exhibit has been configured and installed on your router.
What is the result of applying this policy?
- A. The 172.18.1.0/32 network will be redistributed into OSPF as an external route.
- B. The 172.18.1.0/24 network will be redistributed into OSPF as an internal route.
- C. The 172.18.1.0/32 network will be redistributed into OSPF as an internal route.
- D. The 172.18.1.0/24 network will be redistributed into OSPF as an external route.
Answer: D
NEW QUESTION # 184
Click the Exhibit button. What does IS-IS/18 mean in the output displayed in the exhibit?
- A. These routes are internal Level 1 routes.
- B. These routes are internal Level 2 routes.
- C. These routes are external Level 1 routes.
- D. These routes are external Level 2 routes.
Answer: B
NEW QUESTION # 185
Which configuration can be applied to ensure that no more than 600 MAC addresses are learned by a virtual switch?
- A. Option A
- B. Option C
- C. Option B
- D. Option D
Answer: C
NEW QUESTION # 186
Click the Exhibit button. What does IS-IS/18 mean in the output displayed in the exhibit?
- A. These routes are internal Level 1 routes.
- B. These routes are internal Level 2 routes.
- C. These routes are external Level 1 routes.
- D. These routes are external Level 2 routes.
Answer: B
NEW QUESTION # 187
Which statement correctly describes a characteristic of IPv6 unicast addressing?
- A. Link-local addresses are in the range of FE00::/12.
- B. Only one loopback address exists, ::1/128.
- C. Link-local addresses are in the range of FF00::/8.
- D. Global addresses are in the range of 2002::/16.
Answer: B
NEW QUESTION # 188
The segment touting SRGB start label Is 10,000 and the SRGB index range is 500.
In this scenario, which two statements are correct? (Choose two.)
- A. The first usable label Is 10,000.
- B. The last usable label is 10.501.
- C. The last usable label is 10,499.
- D. The first usable label is 10,001.
Answer: C,D
Explanation:
The Segment Routing Global Block (SRGB) defines a range of MPLS labels reserved for segment routing.
With an SRGB starting label of 10,000 and an index range of 500, the first usable label is indeed 10,001 because label 10,000 is typically reserved and not usedfor forwarding. The last usable label would be 10,499 because the range includes 500 labels starting from 10,001.
References:
Juniper Networks documentation on Segment Routing: Segment Routing Overview
NEW QUESTION # 189
What are two types of SlDs used in segment touting? (Choose two.)
- A. link
- B. adjacency
- C. node
- D. interface
Answer: B,C
Explanation:
https://zartmann.dk/sr-intro/
In segment routing, SIDs (Segment Identifiers) are used to identify different types of segments that can be traversed. A node SID represents an instruction to route a packet to a particular node, and an adjacency SID represents an instruction to route a packet over a specific link or adjacency between two nodes.
References
Juniper Networks Technical Documentation on Segment Routing
NEW QUESTION # 190
Click the Exhibit button.
Referring to the exhibit, you have an established RSVP LSP between R1 and R4 when you experience a link failure between R2 and R3.
Which two statements are correct? (Choose two.)
- A. R2 sends a PathTear message upstream to R1 signaling the link failure.
- B. R3 sends a PathTear message downstream to R4 signaling the link failure.
- C. R3 sends a ResvTear message downstream to R4 signaling the link failure.
- D. R2 sends a ResvTear message upstream to R1 signaling the link failure.
Answer: C,D
Explanation:
Upon a link failure in an RSVP-signaled LSP, the router upstream of the failure (R2) sends a PathTear message upstream to the ingress router (R1), and the router downstream of the failure (R3) sends a ResvTear message downstream to the egress router (R4). These messages signal the failure and initiate tear down of the LSP state in the respective directions.References:
RSVP-TE Overview, Juniper Networks Documentation
Understanding RSVP Signal Failures, Juniper Networks Documentation
NEW QUESTION # 191
Which two statements describe operations performed by the encapsulating tunnel endpoint in an IP-IP tunnel? (Choose two.)
- A. It creates and adds a new inner IP header with the remote destination device's IP address
- B. It decrements the time-to-live (TTL) counter by one in the inner IP header
- C. It adds an outer IP header with the destination address of the remote tunnel endpoint
- D. It modifies the source and destination addresses in the inner IP header
Answer: B,C
NEW QUESTION # 192
Exhibit
Which two statements ate correct about the actions taken as the packet traverses the service provider MPLS network from Site 1 to Site 2 as shown in the exhibit? (Choose two.)
- A. R1 will perform a lookup using the mpls.0 table.
- B. R1 will perform a lookup using the lnet.3 table.
- C. R2 will perform a lookup using the mpls.0 table.
- D. R2 will perform a lookup using the inet.3 table.
Answer: C
NEW QUESTION # 193
......
JN0-363 Exam Dumps Contains FREE Real Quesions from the Actual Exam: https://www.verifieddumps.com/JN0-363-valid-exam-braindumps.html
Free Test Engine Verified By JNCIS-SP Certified Experts: https://drive.google.com/open?id=11m6JxOGcny3JvKnCjJXx5pgnS9Drq_rn
