Check the Available NSE6_FWF-6.4 Exam Dumps with 37 QA's UPDATED 2024
Download NSE6_FWF-6.4 Exam Dumps Questions to get 100% Success in Fortinet
Fortinet NSE6_FWF-6.4 certification is a valuable asset for professionals who are looking to advance their careers in the field of network security. It demonstrates to employers that an individual has the skills and knowledge to design and implement secure wireless LAN solutions, which is becoming increasingly important in today’s digital landscape. Earning this certification can help individuals to stand out in a competitive job market and can open up new opportunities for career advancement.
NEW QUESTION # 15
What is the first discovery method used by FortiAP to locate the FortiGate wireless controller in the default configuration?
- A. Static
- B. DHCP
- C. Multicast
- D. Broadcast
Answer: A
Explanation:
Explanation
According to the web search results, the first discovery method used by FortiAP to locate the FortiGate wireless controller in the default configuration is static. This means that the FortiAP sends discovery requests to a preconfigured IP address that the controller owns. This is useful if the FortiAP and the controller are not in the same subnet and other discovery methods will not work. The other discovery methods are used in sequence if the static method fails or is not configured. References: Advanced WiFi controller discovery | FortiAP / FortiWiFi 7.4.0
NEW QUESTION # 16
Refer to the exhibit.
If the signal is set to -68 dB on the FortiPlanner site survey reading, which statement is correct regarding the coverage area?
- A. Areas with the signal strength equal or stronger than -68 dB are highlighted in multicolor
- B. Areas with the signal strength weaker than -68 dB are highlighted in orange and red to indicate that no signal was propagated by the APs.
- C. Areas with the signal strength weaker than -68 dB are cut out of the map
- D. Areas with the signal strength equal to -68 dB are zoomed in to provide better visibility
Answer: A
NEW QUESTION # 17
What type of design model does FortiPlanner use in wireless design project?
- A. Analytical model
- B. Integration model
- C. Predictive model
- D. Architectural model
Answer: C
NEW QUESTION # 18
Refer to the exhibit.
What does the asterisk (*) symbol beside the channel mean?
- A. Indicates channels that will be scanned by the Wireless Intrusion Detection System (WIDS)
- B. Indicates channels that can be used only when Radio Resource Provisioning is enabled
- C. Indicates channels that cannot be used because of regulatory channel restrictions
- D. Indicates channels that are subject to dynamic frequency selection (DFS) regulations
Answer: D
NEW QUESTION # 19
When deploying a wireless network that is authenticated using EAP PEAP, which two configurations are required? (Choose two.)
- A. A WPA2 or WPA3 Enterprise wireless network
- B. An X.509 to authenticate the authentication server
- C. 509 certificates and work for connections that use Secure Socket Layer/Transport Level Security (SSL/TLS). Both client and server certificates have additional requirements.
- D. An X.509 certificate to authenticate the client
- E. A WPA2 or WPA3 personal wireless network
Answer: B,D
NEW QUESTION # 20
Which factor is the best indicator of wireless client connection quality?
- A. Downstream link rate, the connection rate for the AP to the client
- B. The receive signal strength (RSS) of the client at the AP
- C. The channel utilization of the channel the client is using
- D. Upstream link rate, the connection rate for the client to the AP
Answer: B
Explanation:
SSI, or "Received Signal Strength Indicator," is a measurement of how well your device can hear a signal from an access point or router. It's a value that is useful for determining if you have enough signal to get a good wireless connection.
NEW QUESTION # 21
Refer to the exhibits.
Exhibit A
Exhibit B
The exhibits show the diagnose debug log of a station connection taken on the controller CLI.
Which security mode is used by the wireless connection?
- A. WPA2 Enterprise
- B. Open, with radius MAC filtering
- C. WPA3 Enterprise
- D. WPA2 Personal and radius MAC filtering
Answer: A
Explanation:
Best security option is WPA2-AES.
NEW QUESTION # 22
What is the first discovery method used by FortiAP to locate the FortiGate wireless controller in the default configuration?
- A. Static
- B. DHCP
- C. Multicast
- D. Broadcast
Answer: A
NEW QUESTION # 23
Which statement describes FortiPresence location map functionality?
- A. Provides real-time insight into user online activity
- B. Provides real-time insight into user purchase activity
- C. Provides real-time insight into user movements
- D. Provides real-time insight into user usage stats
Answer: C
NEW QUESTION # 24
Refer to the exhibit.
What does the asterisk (*) symbol beside the channel mean?
- A. Indicates channels that will be scanned by the Wireless Intrusion Detection System (WIDS)
- B. Indicates channels that can be used only when Radio Resource Provisioning is enabled
- C. Indicates channels that cannot be used because of regulatory channel restrictions
- D. Indicates channels that are subject to dynamic frequency selection (DFS) regulations
Answer: D
Explanation:
Explanation
This frequencies are also used by other licensed applications, wireless LANs have to use a specific method to gain access to certain higher frequencies and this method is known as DFS.
NEW QUESTION # 25
Which two phases are part of the process to plan a wireless design project? (Choose two.)
- A. Project information phase
- B. Installation phase
- C. Hardware selection phase
- D. Site survey phase
Answer: A,D
NEW QUESTION # 26
Refer to the exhibit.
What does the asterisk (*) symbol beside the channel mean?
- A. Indicates channels that will be scanned by the Wireless Intrusion Detection System (WIDS)
- B. Indicates channels that can be used only when Radio Resource Provisioning is enabled
- C. Indicates channels that cannot be used because of regulatory channel restrictions
- D. Indicates channels that are subject to dynamic frequency selection (DFS) regulations
Answer: B
NEW QUESTION # 27
Refer to the exhibit.
If the signal is set to -68 dB on the FortiPlanner site survey reading, which statement is correct regarding the coverage area?
- A. Areas with the signal strength equal to -68 dB are zoomed in to providebetter visibility.
- B. Areas with the signal strength weaker than -68 dB are shown with blackbackground.
- C. Areas with the signal strength weaker than -68 dB are highlighted in orangeand red to indicate that no signal was propagated by the APS.
- D. Areas with the signal strength equal or stronger than -68 dB are highlighted in green circles.
Answer: D
Explanation:
Explanation
The FortiPlanner site survey reading is a tool that shows the predicted signal strength of the wireless network based on the floor plan, the placement of the APs, and the propagation model. The signal strength is measured in decibels (dB), which is a logarithmic scale that indicates how much power the signal has. The higher the dB value, the stronger the signal.
The site survey reading allows the user to set a threshold value for the signal strength, which is -68 dB by default. This means that any area with a signal strength equal or stronger than -68 dB is considered to have adequate coverage for most wireless applications. These areas are highlighted in green circles on the floor plan. Any area with a signal strength weaker than -68 dB is considered to have poor coverage or no coverage at all. These areas are shown with different colors, such as yellow, orange, red, or black, depending on how weak the signal is.
Therefore, the correct answer is D. Areas with the signal strength equal or stronger than -68 dB are highlighted in green circles.
References:
FortiPlanner 2.0 User Guide, page 28
FortiPlanner Data Sheet, page 2
FortiPlanner 2.2 User Guide, page 19
NEW QUESTION # 28
When configuring Auto TX Power control on an AP radio, which two statements best describe how the radio responds? (Choose two.)
- A. When the AP detects PF Interference from an unknown source such as a cordless phone with a signal stronger that -70 dBm, it will increase its transmission power until it reaches the maximum configured TX power limit.
- B. When the AP detects any interference from a trusted neighboring AP stronger that -70 dBm, it will reduce its transmission power until it reaches the minimum configured TX power limit.
- C. When the AP detects any wireless client signal weaker than -70 dBm, it will reduce its transmission power until it reaches the maximum configured TX power limit.
- D. When the AP detects any other wireless signal stronger that -70 dBm, it will reduce its transmission power until it reaches the minimum configured TX power limit.
Answer: B,D
Explanation:
Explanation
According to the web search results, Auto TX Power control is a feature that allows the AP to automatically adjust its transmission power based on the RF environment. The goal is to minimize interference and optimize coverage cells for roaming. When the AP detects any other wireless signal stronger than -70 dBm, it means that there is a potential source of interference nearby, so it will reduce its transmission power until it reaches the minimum configured TX power limit. This will reduce the interference and improve coexistence with other devices. When the AP detects any interference from a trusted neighboring AP stronger than -70 dBm, it means that there is a high density of APs in the area, so it will also reduce its transmission power until it reaches the minimum configured TX power limit. This will balance the load and avoid overlapping coverage areas.
References: AP Transmit Power and Enable Power Reduction with Auto TX, Transmit Power and Antenna Configuration, Meraki Auto RF: Wi-Fi Channel and Power Management
NEW QUESTION # 29
When enabling security fabric on the FortiGate interface to manage FortiAPs, which two types of communication channels are established between FortiGate and FortiAPs? (Choose two.)
- A. Data channels
- B. Control channels
- C. Security channels
- D. FortLink channels
Answer: A,B
Explanation:
Explanation
The control channel for managing traffic, which is always encrypted by DTLS. l The data channel for carrying client data packets.
NEW QUESTION # 30
Which two roles does FortiPresence analytics assist in generating presence reports? (Choose two.)
- A. Gathering details about on site visitors
- B. Predicting the number of guest users visiting on-site
- C. Comparing current data with historical records
- D. Reporting potential threats by guests on site
Answer: A,B
NEW QUESTION # 31
......
Best Value Available! 2024 Realistic Verified Free NSE6_FWF-6.4 Exam Questions: https://www.verifieddumps.com/NSE6_FWF-6.4-valid-exam-braindumps.html
100% Accurate Answers! NSE6_FWF-6.4 Actual Real Exam Questions: https://drive.google.com/open?id=1gHO3184TUXGYmoq5FIch5zVLOdzKiYZ5
