Get Instant Access to 300-410 Practice Exam Questions
Reliable Study Materials & Testing Engine for 300-410 Exam Success!
NEW QUESTION # 239
Refer to the exhibit.
Which subnet is redistributed from EIGRP to OSPF routing protocols?
- A. 10.2.2.0/24
- B. 10.2.3.0/26
- C. 10.1.2.0/24
- D. 10.1.4.0/26
Answer: A
NEW QUESTION # 240
Refer to the exhibit.
R1 is being monitored using SNMP and monitoring devices are getting only partial information. What action should be taken to resolve this issue?
- A. Modify the CoPP policy to increase the configured exceeded limit for SNMP.
- B. Modify the access list to include snmptrap.
- C. Modify the CoPP policy to increase the configured CIR limit for SNMP.
- D. Modify the access list to add a second line to allow udp any any eq snmp
Answer: D
NEW QUESTION # 241
An engineer is troubleshooting on the console session of a router and turns on multiple debug commands. The console screen is filled with scrolling debug messages that none of the commands can be verified if entered correctly or display any output. Which action allows the engineer to see entered console commands while still continuing the analysis of the debug messages?
- A. Configure the no logging console debugging command globally
- B. Configure the logging synchronous command
- C. Configure the logging synchronous level all command
- D. Configure the term no mon command globally
Answer: B
Explanation:
Explanation
Let's see how the "logging synchronous" command affect the typing command:
Without this command, a message may pop up and you may not know what you typed if that message is too long. When trying to erase (backspace) your command, you realize you are erasing the message instead.
With this command enabled, when a message pops up you will be put to a new line with your typing command which is very
NEW QUESTION # 242
Drag and drop the MPLS VPN device types from the left onto the definitions on the right.
Answer:
Explanation:
NEW QUESTION # 243
What is a function of the IPv6 DHCP Guard feature for DHCP messages?
- A. All client messages are always switched regardless of the device role.
- B. It blocks only DHCP request messages.
- C. If the device is configured as a DHCP server, no message is switched.
- D. Only access lists are supported for matching traffic.
Answer: B
NEW QUESTION # 244
Refer to the exhibit.
An engineer configured NetFlow on R1, but the NMS server cannot see the flow from ethernet 0/0 of R1. Which configuration resolves the issue?
- A. interface Ethernet0/0
ip flow monitor Flowmonitor1 input
ip flow monitor Flowmonitor1 output - B. flow monitor Flowmonitor1
source Ethernet0/0 - C. flow exporter FlowAnalyzer1
source Ethernet0/0 - D. interface Ethernet0/1
ip flow monitor Flowmonitor1 input
ip flow monitor Flowmonitor1 output
Answer: A
NEW QUESTION # 245
Refer to the exhibit.
The R2 loopback interface is advertised with RIP and EIGRP using default values. Which configuration changes make R1 reach the R2 loopback using RIP?
- A. R1(config)# router rip
R1(config-router)# distance 90 - B. R1(config)# router eigrp 1
R1(config-router)# distance eigrp 120 120 - C. R1(config)# router rip
R1(config-router)# distance 100 - D. R1(config)# router eigrp 1
R1(config-router)# distance eigrp 130 120
Answer: D
Explanation:
distance (AD Number u want to change to) (neighbor IP) (Wildcard Mask) (access-list number)
NEW QUESTION # 246
A company is expanding business by opening 35 branches over the Internet. A network engineer must configure DMVPN at the branch routers to connect with the hub router and allow NHRP to add spoke routers securely to the multicast NHRP mappings automatically Which configuration meets this requirement at the hub router?
- A.
- B.
- C.
- D.
Answer: B
Explanation:
The command "ip nhrp map multicast dynamic" allows NHRP to automatically add spoke routers to the multicast NHRP mappings.
NEW QUESTION # 247 
Refer to the exhibit. Which action restores the routes from neighbors while still filtering 1.1.1.0/24?
- A. Modify the route map to permit the access list instead of deny it
- B. Add a second sequence in the route map permit 20
- C. Modify the access list to deny instead of permit it.
- D. Add a second line in the access list to permit any.
Answer: B
NEW QUESTION # 248
Drag and Drop Question
Drag and drop the MPLS terms from the left onto the correct definitions on the right.
Answer:
Explanation:
NEW QUESTION # 249
Refer to the exhibit.
Network operations cannot read or write an configuration on the device with this configuration from the operation subnet.
Which two configuration fix the issue? (Choose two.)
- A. Configure SNMP rw permission in addition to version 1.
- B. Modify SNMP rw permission in addition to version 1.
- C. Modify access list 1 and allow operations subnet in the access list.
- D. Configure SNMP rw permission in addition to community ciscotest 1.
- E. Configure SNMP rw permission in addition to community ciscotest.
Answer: C,E
NEW QUESTION # 250
Refer to the exhibit.
Which statement about R1 is true?
- A. OSPF redistributes RIP routes only if they have a tag of one.
- B. RIP routes are redistributed to OSPF without any changes.
- C. RIP learned routes are distributed to OSPF with a tag value of one.
- D. R1 adds one to the metric for RIP learned routes before redistributing to OSPF.
Answer: C
NEW QUESTION # 251
Drag and drop the SNMP attributes in Cisco IOS devices from the left onto the correct SNMPv2c or SNMPV3 categories on the right.
Answer:
Explanation:
NEW QUESTION # 252
Refer to the exhibit.
During troubleshooting it was discovered that the device is not reachable using a secure web browser. What is needed to fix the problem?
- A. permit udp port 465
- B. permit tcp port 443
- C. permit tcp port 465
- D. permit tcp port 22
Answer: B
NEW QUESTION # 253
Refer to the exhibit.
Why is the remote NetFlow server failing to receive the NetFlow data?
- A. The flow monitor is applied in the wrong direction.
- B. The flow exporter is configured but is not used.
- C. The destination of the flow exporter is not reachable.
- D. The flow monitor is applied to the wrong interface.
Answer: B
NEW QUESTION # 254
Refer to the exhibit.
Network operations cannot read or write any configuration on the device with this configuration from the operations subnet. Which two configurations fix the issue? (Choose two.)
- A. Configure SNMP rw permission in addition to version 1.
- B. Modify access list 1 and allow operations subnet in the access list.
- C. Configure SNMP rw permission in addition to community ciscotest 1.
- D. Modify access list 1 and allow SNMP in the access list.
- E. Configure SNMP rw permission in addition to community ciscotest.
Answer: B,E
NEW QUESTION # 255
Refer to the exhibit. An engineer must establish multipoint GRE tunnels between hub router R6 and branch routers R1, R2, and R3. Which configuration accomplishes this task on R1?
A)
B)
C)
D)
- A. Option C
- B. Option B
- C. Option D
- D. Option A
Answer: C
NEW QUESTION # 256
Refer to the exhibit.
Which subnet is redistributed from EIGRP to OSPF routing protocols?
- A. 10.2.2.0/24
- B. 10.2.3.0/26
- C. 10.1.2.0/24
- D. 10.1.4.0/26
Answer: A
NEW QUESTION # 257
R1 and R2 are configured as eBGP neighbor , R1 is in AS100 and R2 is in AS200. R2 is advertising these networks to R1:
The network administrator on R1 must improve convergence by blocking all subnets of 172-16.0.0/16 major network with a mask lower than 23 from coming in, Which set of configurations accomplishes the task on R1?
- A. access-list 1 deny 172.16.0.0 0.0.254.255
access-list 1 permit any
!
router bgp 100
neighbor 192.168.100.2 remote-as 200
neighbor 192.168.100.2 distribute-list 1 in - B. ip prefix-list PL-1 deny 172.16.0.0/16
ip prefix-list PL-1 permit 0.0.0.0/0
!
router bgp 100
neighbor 192.168.100.2 remote-as 200
neighbor 192.168.100.2 prefix-list PL-1 in - C. ip prefix-list PL-1 deny 172.16.0.0/16 ge 23
ip prefix-list PL-1 permit 0.0.0.0/0 le 32
!
router bgp 100
neighbor 192.168.100.2 remote-as 200
neighbor 192.168.100.2 prefix-list PL-1 in - D. ip prefix-list PL-1 deny 172.16.0.0/16 le 23
ip prefix-list PL-1 permit 0.0.0.0/0 le 32
!
router bgp 100
neighbor 192.168.100.2 remote-as 200
neighbor 192.168.100.2 prefix-list PL-1 in
Answer: D
NEW QUESTION # 258
Drag and drop the DHCP messages from the left onto the correct uses on the right.
Answer:
Explanation:
Reference:
DHCPINFORM: If a client has obtained a network address through some other means or has a manually configured IP address, a client workstation may use a DHCPINFORM request message to obtain other local configuration parameters, such as the domain name and Domain Name Servers (DNSs). DHCP servers receiving a DHCPINFORM message construct a DHCPACK message with any local configuration parameters appropriate for the client without allocating a new IP address. This DHCPACK will be sent unicast to the client.
DHCPNAK: If the selected server is unable to satisfy the DHCPREQUEST message, the DHCP server will respond with a DHCPNAK message. When the client receives a DHCPNAK message, or does not receive a response to a DHCPREQUEST message, the client restarts the configuration process by going into the Requesting state. The client will retransmit the DHCPREQUEST at least four times within 60 seconds before restarting the Initializing state.
DHCPACK: After the DHCP server receives the DHCPREQUEST, it acknowledges the request with a DHCPACK message, thus completing the initialization process.
DHCPDECLINE: The client receives the DHCPACK and will optionally perform a final check on the parameters. The client performs this procedure by sending Address Resolution Protocol (ARP) requests for the IP address provided in the DHCPACK. If the client detects that the address is already in use by receiving a reply to the ARP request, the client will send a DHCPDECLINE message to the server and restart the configuration process by going into the Requesting state.
https://www.cisco.com/c/en/us/support/docs/ip/dynamic-address-allocation-resolution/27470-100.html
NEW QUESTION # 259
An engineer configured access list NON-CISCO in a policy to influence routes
What are the two effects of this route map configuration? (Choose two.)
- A. Packets are forwarded to the default gateway.
- B. Packets are evaluated by sequence 10.
- C. Packets are dropped by the access list.
- D. Packets are not evaluated by sequence 10.
- E. Packets are forwarded using normal route lookup.
Answer: A,B
NEW QUESTION # 260
Refer to the exhibit.
An engineer is trying to redistribute OSPF to BGP, but not all of the routes are redistributed. What is the reason for this issue?
- A. By default, only internal routes and external type 1 routes are redistributed into BGP
- B. BGP convergence is slow, so the route will eventually be present in the BGP table
- C. By default, only internal OSPF routes are redistributed into BGP
- D. Only classful networks are redistributed from OSPF to BGP
Answer: C
Explanation:
Explanation
If you configure the redistribution of OSPF into BGP without keywords, only OSPF intra-area and inter-area routes are redistributed into BGP, by default.
You can redistribute both internal and external (type-1 & type-2) OSPF routes via this command:
Router(config-router)#redistribute ospf 1 match internal external 1 external 2 Reference:
https://www.cisco.com/c/en/us/support/docs/ip/border-gateway-protocol-bgp/5242-bgp-ospf-redis.html
NEW QUESTION # 261
Refer to the exhibit.
An engineer has configured R1 as EIGRP stub router. After the configuration, router R3 failed to reach to R2 loopback address.
Which action advertises R2 loopback back into the R3 routing table?
- A. Use a leak map on R1 that matches the required prefix and apply it with the distribute list command toward R3.
- B. Add a static null route for R2 loopback address in R1 and redistribute it to advertise to R3.
- C. Add a static route for R2 loopback address in R1 and redistribute it to advertise to R3.
- D. Use a leak map on R3 that matches the required prefix and apply it with the EIGRP stub feature.
Answer: A
Explanation:
Explanation
The EIGRP stub feature is useful to prevent unnecessary EIGRP queries and to filter some routes that you advertise. What if you want to configure your router as a stub router but still make an exception to some routes that it advertises? That is possible with the leak-map feature. This is how to configure leak-map in this question:
R1(config)#ip access-list standard R2_L0
R1(config-std-nacl)#permit host 2.2.2.2
R1(config)#route-map R2_L0_LEAK
R2(config-route-map)#match ip address R2_L0
R1(config)#router eigrp 1
R1(config-router)#eigrp stub leak-map R2_L0_LEAK
NEW QUESTION # 262
......
Validate your Skills with Updated 300-410 Exam Questions & Answers and Test Engine: https://www.verifieddumps.com/300-410-valid-exam-braindumps.html
Tested & Approved 300-410 Study Materials Download: https://drive.google.com/open?id=1jLU2_NJQoDY3VCuFuobbYd60sCdk5iSY
