Latest Cisco 300-425 PDF and Dumps (2021) Free Exam Questions Answers
Pass Your CCNP Enterprise 300-425 Exam on Nov 11, 2021 with 99 Questions
The Cisco 300-425 test entails the creation of Cisco wireless networks for the enterprise. You pick it from six tests known as concentration. On its own, such an exam helps in coming by the Cisco Certified Specialist-Enterprise Wireless Design certification. Also, since it comes after the core 350-401 test, succeeding in it means you get to possess the CCNP Enterprise certificate.
NEW QUESTION 51
An engineer is conducting a Layer 2 site survey. Which type of client must the engineer match to the survey?
- A. worst client available
- B. best client available
- C. normal client
- D. phone client
Answer: A
Explanation:
Explanation
https://www.cisco.com/c/en/us/support/docs/wireless/5500-series-wireless-controllers/116057-site-survey-gu
NEW QUESTION 52
A network engineer is working on a design for a wireless network that must support data, voice, and location services. To support these services, which access point placement must the engineer use?
- A. perimeter only
- B. indoor and outdoor
- C. perimeter and corner
- D. corner only
Answer: A
NEW QUESTION 53 
Refer to the exhibit. A client roams between two APs that are registered to two different controllers, where each controller has an interface in the client subnet. Both controllers are running AireOS. Which scenario explains the client roaming behavior?
- A. Controllers do not exchange mobility control messages (over UDP port 16666) and the client database entry is not moved from the original controller to the new controller.
- B. Controllers exchange mobility control messages (over UDP port 16666) and the client database entry is moved from the original controller to the new controller.
- C. Controllers exchange mobility control messages (over UDP port 16666) and the client database entry is tunneled from the original controller to the new controller.
- D. Controllers exchange mobility control messages (over UDP port 16666) and a new client session is started with the new controller.
Answer: B
Explanation:
Section: Mobility
Explanation
NEW QUESTION 54
Which UDP port numbers are used for exchange mobility packets in an AireOS wireless deployment?
- A. UDP 16668 for control plane, UDP 16667 for data plane
- B. UDP 16666 for control plane, UDP 16667 for data plane
- C. UDP 16667 for control plane, UDP 16666 for data plane
- D. UDP 16666 for control plane, EoIP (IP protocol 97) for data plane
Answer: B
Explanation:
NEW QUESTION 55
Drag and drop the characteristics from the left onto the correct functionalities on the right.
Answer:
Explanation:
Explanation:
https://www.cisco.com/c/en/us/td/docs/wireless/controller/7-4/configuration/guides/consolidated/b_cg74_CONSOLIDATED/b_cg74_CONSOLIDATED_chapter_010100001.html
NEW QUESTION 56
An engineer is using a Cisco AIR-2702i AP to conduct a Layer 1 site Survey, which mode is selected for the AP to discover non-Wi-Fi interference with metageek chanalyzer?
- A. Monitor
- B. FlexConnect
- C. Sniffer
- D. SE-connect
Answer: D
NEW QUESTION 57
An engineer must ensure that the wireless network can accomplish fast secure roaming by way of caching keys on the access points. Which key caching mechanism is enabled by default on a Cisco AireOS WLC?
- A. 802.11r
- B. SKC
- C. CCKM
- D. OKC
Answer: D
Explanation:
NEW QUESTION 58
During a post-deployment site Survey, issues are found with non wi-Fi interference. What should the engineer use to identify the source of the Interference?
- A. Wireshark
- B. Cisco spectrum expert
- C. Network analysis module
- D. Wireless intrusion prevention
Answer: B
NEW QUESTION 59
A customer has two Cisco 550B WLCs that manage all the access points in their network and provide N+1 redundancy and load balancing. The primary Cisco WLC has 60 licenses and the secondary Cisco WLC has
40. The customer wants to convert the N+1 model to an HA model and provide SSO. Configuration must be performed during a maintenance window. After performing all the configurations on both controllers, the config redundancy unit secondary command is issued on the secondary Cisco WLC and it fails. Which parameter needs to be in place to complete the configuration?
- A. A cable in the RP port
- B. SSO needs to be enabled
- C. The primary Cisco WLC is already set as the secondary unit.
- D. The secondary Cisco WLC needs a minimum of 50 base licenses
Answer: D
Explanation:
NEW QUESTION 60
What is the recommended cell overlap when designing a wireless network for Cisco Hyperlocation?
- A. 40%
- B. 30%
- C. 50%
- D. 20%
Answer: D
Explanation:
NEW QUESTION 61
A network engineer is designing a new wireless network. The network needs to have these characteristics:
* support high client concentration
* optimize client performance
* avoid interference
Which approach should be taken?
- A. Deploy APs near each other for 5 GHz coverage, and enable me 2.4 GHz radios for all APs.
- B. Deploy APs near each other for 5 GHz coverage, and disable the 2 4 GHz radios for some APs
- C. Deploy APs near each other for 2 4 GHz coverage, and disable the 5 GHz radios for some APs
- D. Deploy APs near each other for 2 4 GHz coverage and disable the 5 GHz radios for all APs
Answer: A
Explanation:
https://www.cisco.com/c/en/us/td/docs/wireless/controller/technotes/8-6/b_Cisco_Wireless_LAN_Controller_Configuration_Best_Practices.html
NEW QUESTION 62
A wireless engineer must optimize RF performance for multiple buildings with multiple types of construction and user density. Which two actions must be taken? (Choose two.)
- A. Configure Flexconnect groups for each building.
- B. Enable DTPC on the network.
- C. Configure RF profiles for each area type.
- D. Configure AP groups for each area type.
- E. Configure WMM profiles for each building.
Answer: C,D
Explanation:
https://www.cisco.com/c/en/us/td/docs/wireless/controller/8-10/config-guide/b_cg810/configuring_ap_groups.html
NEW QUESTION 63
An engineer must speed up the reauthentication delays that are being experienced on the wireless infrastructure by deploying a key-caching mechanism. Which mechanism must be configured?
- A. GTK-randomization
- B. PEAP
- C. PMF
- D. FT
Answer: D
Explanation:
NEW QUESTION 64
A customer has two Cisco 550B WLCs that manage all the access points in their network and provide N+1 redundancy and load balancing. The primary Cisco WLC has 60 licenses and the secondary Cisco WLC has 40. The customer wants to convert the N+1 model to an HA model and provide SSO. Configuration must be performed during a maintenance window. After performing all the configurations on both controllers, the config redundancy unit secondary command is issued on the secondary Cisco WLC and it fails. Which parameter needs to be in place to complete the configuration?
- A. A cable in the RP port
- B. SSO needs to be enabled
- C. The primary Cisco WLC is already set as the secondary unit.
- D. The secondary Cisco WLC needs a minimum of 50 base licenses
Answer: D
Explanation:
NEW QUESTION 65
Which statement about the 9800 Series Wireless Controller mobility tunnel on a Cisco Catalyst 9800 controller is true?
- A. It is a CAPWAP tunnel with data path only.
- B. It is an IPsec tunnel with control path and data path.
- C. It is a CAPWAP tunnel with control path and data path.
- D. It is an IPsec tunnel with control path only.
Answer: C
Explanation:
NEW QUESTION 66
A company has 10 access point licenses available on their backup Cisco WLC and their primary Cisco WLC is at full capacity, 5 access points are set to high failover priority and 7 access points are set to critical failover priority. During a failure, not all critical access points failed over to the backup Cisco WLC. Which configuration is the cause of this issue?
- A. The critical priority access point count is oversubscribed.
- B. network ap-priority is set to enable.
- C. network ap-priority is set to disable.
- D. The high priority access point is oversubscribed.
Answer: D
Explanation:
https://www.ciscolive.com/c/dam/r/ciscolive/emea/docs/2016/pdf/BRKCOL-2275.pdf
NEW QUESTION 67
Which UDP port numbers are used for exchange mobility packets in an AireOS wireless deployment?
- A. UDP 16668 for control plane, UDP 16667 for data plane
- B. UDP 16666 for control plane, UDP 16667 for data plane
- C. UDP 16667 for control plane, UDP 16666 for data plane
- D. UDP 16666 for control plane, EoIP (IP protocol 97) for data plane
Answer: B
Explanation:
Section: Mobility
NEW QUESTION 68
A network engineer is preparing for an office site survey with a height of 2.5 meters. Which three components are recommended to complete the survey? (Choose three.)
- A. Use DoS attack on APs while measuring the throughput.
- B. Use a drawing of the office space to draw AP and client placements.
- C. Use APs with directional antennas.
- D. Use a battery pack to power APs.
- E. Use APs with built-in antennas.
- F. Use APs with external antennas.
Answer: B,D,E
Explanation:
Section: Wireless Site Survey
NEW QUESTION 69
Which statement about the 9800 Series Wireless Controller mobility tunnel on a Cisco Catalyst 9800 controller is true?
- A. It is a CAPWAP tunnel with data path only.
- B. It is an IPsec tunnel with control path and data path.
- C. It is a CAPWAP tunnel with control path and data path.
- D. It is an IPsec tunnel with control path only.
Answer: C
Explanation:
NEW QUESTION 70
A customer is concerned about mesh backhaul link security. Which level of encryption does the backhaul link use?
- A. 3DES
- B. WEP
- C. hash
- D. AES
Answer: D
Explanation:
NEW QUESTION 71
You made changes to a VLAN, but the changes were not propagated to the other switches in the VTP domain.
You enter a show vtp command at the switch where the changes were made, which displays the following output:
What should you do to solve this problem?
- A. Change the VTP operating mode to server.
- B. Upgrade the VTP version to version 2.
- C. Upgrade the VTP version to version 3.
- D. Disable VTP pruning.
Answer: A
Explanation:
The output of the show vtp command shows that the VTP operating mode is transparent mode. This means that you can make VLAN changes on the switch, but they will only affect that switch. Changes will not be propagated to other switches in the Layer 2 network. You will need to change the operating mode to server if you want to VLAN changes to be propagated to other switches.
To change the VTP operating mode to server, you would enter the vtp server global command as shown:
switch1#(config) vtp server
You should not disable VTP pruning. This will have no effect on the propagation. You must change the mode of the switch.
You should not upgrade the VTP version to version 2 or version 3. This will have no effect on the propagation.
You must change the mode of the switch.
Objective:
Layer 2 Technologies
Sub-Objective:
Configure and verify trunking
References:
Cisco > Cisco IOS LAN Switching Command Reference > udld through vtp v2-mode > vtp server
NEW QUESTION 72
A company wants to replace its existing PBX system with a new VoIP System that will include wireless IP phones. The CIO has concerns about whether the company's existing wireless network can support the new system. Which tool in Cisco Prime can help ensure that the current network will support the new phone system?
- A. Location Readiness
- B. Site Calibration
- C. Voice Readiness
- D. Map Editor
Answer: C
Explanation:
NEW QUESTION 73
An engineer must ensure that the wireless network can accomplish fast secure roaming by way of caching keys on the access points. Which key caching mechanism is enabled by default on a Cisco AireOS WLC?
- A. 802.11r
- B. SKC
- C. CCKM
- D. OKC
Answer: D
Explanation:
NEW QUESTION 74
An engineer must decide the cell overlap for a wireless voice deployment. Which Cisco measurement recommendation should be considered?
- A. One AP should be deployed per 3000 square feet.
- B. The measurement should be done on the 2.4-GHz band.
- C. The edge of the cell should be below 35 RSSI.
- D. The edge of the cell should be -67 dBm.
Answer: D
Explanation:
NEW QUESTION 75
......
300-425 Dumps for CCNP Enterprise Certified Exam Questions & Answer: https://www.verifieddumps.com/300-425-valid-exam-braindumps.html
300-425 Free Exam Study Guide! (Updated 99 Questions): https://drive.google.com/open?id=1mZe8LonF22uzlvGLyX9DCTzR_sDPrFXm
